belt fastener and installation tool,belt fastener machine

The urgency of washing companies to improve finishing processes such as ironing production is even higher than washing.  If a high-efficiency ironing production unit is used to replace the original inefficient units, it will not only reduce the number of operators and work. Area, and due to higher concentration of work, it will also reduce inefficient energy consumption. There are two aspects of waste in ironing operations that are not easy to observe:  One is that the work is discontinuous waiting for idling due to various reasons; Second, the feed pitch is too large, especially when the working speed is high, it seems that everyone is busy and busy, in fact, the output per unit time is not high, and the energy consumption ratio will also increase. Therefore, for ironing production management, what needs to be improved most is the "mandatory beat". Either the equipment should not start with heating, or it must reach the continuous maximum output ra...

There is no doubt that, the through ironing machine is the best equipment in ironing bedsheets linen. The earliest recorded that this ironer was produced in 1955, with its biggest advantages making the double layers lined series more smoothly and high efficiency. On the other hand, everything have two sides, this through ironing machine also have the disadvantages of high cost, need very strictly working environment like steam bar and temperature requirement, even the ironing speed not keep up with roller ironer in some special cases. About the instruction, do you know? Through flatwork ironer mainly instructions are as below: 1.  Ironing Slot :  this is a very safe storage steam device. 2.  Roller . In order to make the cloth fully contact the felt, a better ironing effect can be achieved. 3. Spring : The spring is placed between the roller and the felt and is wrapped around the rotating roller for cushioning. The spring is very dur...

Felt: felt is the necessary consumable for automatic flatwork ironer. It must be emphasized here that the loss process of felt cannot be calculated.  The steam pressure in each factory is different, the steam temperature is different, the steam quality is different, the quality of the linen type is different, and the water content of the linen is different. These will affect the consumption of felt.  When ironing, minimizing the interval between linens can effectively extend the life of the felt. In other words, the felt can be used longer when ironing is kept within 10 cm of each linen. Wax: Special waxes are used for slotting. Generally, the trough iron needs to pass through the trough body with wax cloth with wax for 3 or 4 hours. (click pictures to view our website) Guiding belt / Guide tape: There is no special requirement for the grooved hot guiding tape. Of course, the thinner the guiding tape is, the more obvious the iron marks are, bu...

Common troubleshooting methods and characteristics for industrial flatwork ironing machine 1. Common faults: Ironing machine ironing rollers heat up slowly. (1) Reason: The steam pressure is too low. Solution: Increase steam pressure. (2) Cause: There is water inside the main ironing roller, and the trap is not working properly. Solution: Repair or replace the trap and release the water on the main ironing roller. (3) The siphon is damaged or incorrectly positioned. Solution: Repair the siphon. 2. common failures: fabrics are often damaged when ironing. (1) Reason: The ironing belt is too tight. Solution: Adjust the tightness of the ironing belt. (2) The ironing buckle has burrs. Solution: repair glitches 3. Common faults: The ironing belt often moves during the work. (1) Reason: The length of the two sides of the ironing belt varies. Solution: Change the ironing belt or the position of the picture belt. (2) Reason: The two sides of the spring with the tensioning sha...

In the beginning of 2019, we had visited a laundry factory, in order to better know the situation. And also know some problems on working process, at the same time to improve our products. Anyway, it's a good experience, and worthy this day! Believing that people who have seen my blog have a general understanding of the products we operate. We produce spare parts for flatwork ironer, such as: 1. ironer padding,ironer belt 2. guide tapes, ironer table padding 3. folding cotton belt, polyester feeding belt 4. belt fasteners, and matching machine 5. wax powder, cleaning padding and so on. More info can visit the following video: Or contact me directly: Email:hkxinyun@hkxinyun.com Whatsapp:+86 15919344021 Skype: hk.felting http://www.feltbelteast.com/c/laundry-accessories_0009 http://feltbelt.com/cpzx.asp?topid=2

Flatwork ironer commercial laundry folding working We provide many laundry belts parts as belows: 1) Padding 2) Ironer belt 3) Folding cotton belt 4) Guide tapes: Nomex, polyester 5) Polyester feeding belt 6) belt fasteners 7) belt fasteners machine and other matching products 8) non-skid belt More info please contact me at: Email:hkxinyun@hkxinyun.com Whatsapp:+86 15919344021 Skype: hk.felting http://feltbelt.com/cpzx.asp?topid=2 http://en.feltbelteast.com/l-010-flatwork-ironer-padding-p00011p1.html